Search
Products

You are here: Home > Products > Solid State Relays

Product Details

DC solid state relay with over-current and over-voltage protection

1. Electromagnetic coupling isolation between input and output circuits.

2. Control signal and PLC, TTL logic interface.

3. Light-emitting diode indicates working status.

4. Built-in input under voltage protection, output transient overv oltage absorption protection.

5. Solid non-contact output, fast switching speed, no spark and no arcing on and off.

6. Epoxy resin encapsulation in one, anti-corrosion, fire and shock resistance, switch work stable and reliable.

7. The product is mainly used in the new energy vehicles of high-power DC appliances without contact switch. Such as PTC DC heater, battery charging and discharging, DC motor, solenoid valve and other switching switches.


Model

GDR08LA (over-current protection), GDR08ZA (short-circuit protection)

Input parameters

Control power

12~15 VDC

18~36 VDC

Control current

30~80 MA

25~70 MA

Under voltage protection

<10VDC self-locking

<16VDC self-locking

On-off time

< 250ΜS (120A-200A); <500μS (300A-2000A)

Working indication

LED

Output parameters

Maximum output voltage

100VDC 200VDC 600VDC 1200VDC

Max. load current

120, 150, 180, 200, 300...... 2000 A

On-state voltage drop

≤1.0 ~ 4.0 V

Off-state Voltage

≥100V ≥200V ≥600V ≥1200V

Over voltage protection

Transient protection voltage are: 80V, 180V, 470V, 1000V

Protection current

Overcurrent: 50% of the marked current setting; Short circuit: 100% of the marked current setting

Switching characteristics

MOS or IGBT-solid-state non-contact switching characteristics


Performance Parameters

Isolation voltage

≥ 1800~2500 V

Insulation voltage

≥ 2000 To 2500 V

Operating temperature

-25~75℃

Insulation resistance

100 MΩ

Heat dissipation condition

With heat sink and then add fan strong cooling

Safety factor of load current

2.5-4 Times for resistive load, 3-6 times for inductive load

Dimension

95×39×48 / 120×52×40 / 135×69×50 mm


Selection Tips:

Because the load voltage value in the parameter table is equal to the off-state voltage value, and the load current is the maximum peak current at room temperature, so there should be a margin when selecting the voltage and current of the product. When resistive load: current is selected according to 2.5~4 times load current, voltage is selected according to 2~2.5 times load power. Inductive load: the current is selected according to 3-7 times the load current, and the voltage is selected according to 2.5-3 times the load voltage.


According to the relationship between the load current and the ambient temperature, when the ambient temperature is high or the heat dissipation conditions are not good, also correspondingly increase the current capacity of the solid state relay.


For inductive loads, a freewheeling diode must be connected to both ends of the load, and a varistor (MOV) must be connected to the output (1 to 1.5 times the supply voltage) to prevent damage to the solid-state switch from the high voltage generated during switching.


The series products are equipped with load over current and short-circuit protection functions, and when the load over current or short-circuit occurs in the main circuit, it can quickly close the self-locking, effectively protecting the solid-state switch itself from burning function.


When the product is installed, it is required that the contact surface between the heat sink and this product must be flat and clean, and a layer of thermally conductive silicone grease must be applied to its surface, and finally the screws set with flat washers and spring washers are tightened and fixed symmetrically.

Product Inquiry
If you would like a quotation or further information about this product, please fill in the form below and we will reply to you soon.
看不清?点击更换